cncgunsparts.com
306 Maegeo Dr
Lexington, NC 27292
United States
ph: 336-253-3804
cncguns
Some time ago, I started researching the 7.62x25 caliber uppers to use with my registered M-16 lower; everything I found seemed to work the same as 9mm blow back uppers. From time to time, we have all heard this set up will damage an AR-15 or M-16 lower so I wanted something better.
Now we can offer you the new Gas Operated 7.62x25mm AR-15 or M-16 upper
Prices and Descriptions subject to change without Notice.
Our uppers are made with a stainless steel barrel, custom-made gas tub, and custom-built bolt. The bolt carrier is a standard AR-15 or M-16 carrier
To order go to the order form page. Please reference the Order# below for your upper selection and include any additional items you wish to purchase ie. Mags, Drum, etc.
16-inch 7.62x25 C.A.R. Upper AR-15 Order # 16CAR-A3AR15
16-inch 7.62x25 C.A.R. Upper M-16 Order # 16CAR-A3M16
101/2-inch 7.62x25 SBR Upper AR-15 Order# 101/2 SBR-A3AR15
101/2-inch 7.62x25 SBR Upper M-16 Order# 101/2 SBR-A3M16
Standard upper price is $POR for M-16 upper and $POR for AR-15 upper , with mag block and one 35 round mag, custom-built bolt. and carrier
We Cannot Ship to nor accept orders larger then 10 ROUNDS per magazine from CALIFORNIA, NEW YORK CITY, WASHINGTON D.C./ MASSACHUSETS. HAWAIAN RESIDENTS MARYLAND. NEW JERSEY if ordering a upper you will receive 10 round mags
Our Mag blocks are made totally from steel, flush mount, top drop in mag block with a built in feed ramp, and use the standard AR-15 M-16 mag release.
Mag block Price is $POR
Mags have a slot cut in them so the standard AR Mag Catch secures the Mag in its proper location.
Custom built 72 round drums for 7.62x25mm and 9mm AR-15 M-16 and
sten converted M-11/9
Custom build 72 round drum with purchase of upper Price is
Custom build 72 round drum Price is $POR
Yes, the drums do work in a full auto weapon just click the link below to see the fun
http://www.youtube.com/watch?v=XBR0AT3ZCGI
Please check local laws for magazine capacity restrictions.
Magazines restrictions apply to:
CA, HI, MA, MD, NJ, NY
We cannot ship anywhere outside of the United States
Mags for 7.62x25 AR-15 M-16 uppers
Mags for 7.62x25mm Price is $POR each
Mags have a slot cut in them so the standard AR Mag Catch secures the Mag in its proper location.
Please check local laws for magazine capacity restrictions.
Magazines restrictions apply to:
CA, HI, MA, MD, NJ, NY
We cannot ship anywhere outside of the United States
our new 60 round mag on right, and on the left is a 35 round mag The price of the new 60 round mags will be $POR + shipping with purchase of upper e-mail for Availability
60 round Mags for 7.62x25mm if not purchasing a upper the Price is $POR + shipping
e-mail for Availability
Please check local laws for magazine capacity restrictions.
Magazines restrictions apply to:
CA, HI, MA, MD, NJ, NY
We cannot ship anywhere outside of the United States
Mags for 7.62x25mm Price is $POR each
Mags have a slot cut in them so the standard AR Mag Catch secures the Mag in its proper location.
Please check local laws for magazine capacity restrictions.
Magazines restrictions apply to:
CA, HI, MA, MD, NJ, NY
Yes, we are shooting corrosive surplus ammo, as for cleaning the gun barrel its stainless steel. I left an upper for two weeks without cleaning to see what would happen. All that was needed is standard cleaning I would normally do after a day of shooting. Run a brush in the bore and use the AR-15 M-16 chamber brush then run a patch with some Hoppe’s #9 three times down the bore. I then take my bolt and carrier apart, and use a patch with hoppe’s to clean all parts. I have never needed to clean my gas tube; however, I do know some people use pipe cleaners with hoppe’s #9 and running it into the gas tub.
As for shooting, it is smooth, about the same as a 223 upper but does not have the chop of a 9mm blow back upper. There is no need to worry about damaging the lower as this system uses the same parts as a standard 223 upper.
Please keep a checking back as we have other products in a testing stage and will added them as time permits. I also have some M-11/9 parts so if you need something please feel free to send an e-mail and see if we can help you.
Copyright 2009 cnc gun parts. All rights reserved.
cncgunsparts.com
306 Maegeo Dr
Lexington, NC 27292
United States
ph: 336-253-3804
cncguns